Once you have come to terms with what you want to make, the next most important step is space consideration. The amount of space you will need is directly proportional to the size of the items that you will be making. For example, if you want to make small craft projects, and you only require a scroll saw and perhaps a few assorted hand tools, space will be minimal. However if you intend to get into cabinetry, the space requirements increase significantly, in order to accommodate a table saw, and numerous other large bench tools. Most people interested in a large workshop will setup in the basement or the garage.

Next, you will want to make sure any workspace you choose is dry, or can be kept dry through the use of a dehumidifier. Most bench tools have uncoated steel tables which will rust with time. Additionally, if there is any chance of flooding or sewer backup (in the case of a basement), you will want to make sure your tools are elevated off the floor. It's not only bad for the equipment, but a serious safety hazard as well.

Once you have determined you have a dry area to work with, you will need to examine the power requirements of the equipment you will be using.  Higher horsepower equipment will need to be run on 220v - even though some will run less smooth on 110v. Most homes have 220v capability but usually require rewiring to accomplish it. Be sure to consult a qualified electrician before making any decisions on wiring. Obviously if you'll be making small projects, most smaller bench tools and hand tools run on 110v.

Next, you have to tackle the dust collection and ventilation issue, which is also an issue of space and power. Hardwood dust is dangerous from a health perspective, and all wood dusts present a potential fire hazard. Dust collection equipment comes in all shapes and sizes from HEPA filtered shop vacs to sophisticated systems that collect dust at the source and route to a large fabric bag - all with different collection efficiencies. In addition, there are room filtration systems to remove the very fine (and much more dangerous) dust particles from the air.

Now that you have an idea of what you want to build and you're certain you have the space and power, you can start planning which tools you need and design a room layout. There are many online resources that can help you plan your shop layout!

As stated earlier, it's much better to get a head start and determine what you want to build before investing money in a lot of equipment, as you will end up with a lot of stuff you don't need. Here, you can get over 14,000 woodworking plans, for every type of project imaginable. Not only will you get a head start, but also have at your disposal a lifetime supply of plans and inspirations!

Post from: Woodworking Training

Interested in Carpentry Woodworking? The Secret to Success is in the Plans

In these hard economic times business is very hard. If you are a company director looking for a bit of advice because your carpentry business is struggling, you have come to the right place. I have created many articles which try to help a director take the right steps in either closing his business or pre-packing a sale and starting again.

Firstly if your carpentry company is insolvent you have a duty as a director to close the company and not incur any further debt, unless you can be pretty sure that you can put in place a rescue plan to turn that business around. If you can’t them you need to liquidate the company yourself or take professional advice on how best to close the business in an orderly fashion.

By far the most popular choice is to engage an insolvency practitioner to call a meeting of creditors on your behalf, prepare the statement of affairs, hold the meeting and then deal with all the procedural aspects necessary to make sure all creditors now what is going on and how they can participate in any dividend.

There is a fee for all this and generally it will be about £5000 whoever you use around the country. There are some advertisements for liquidations at less than this but by the time all costs are accounted for, it will still come in at about the same sum.

These costs can come out of the assets of the carpentry company and indeed many businesses do have just enough assets or cash to take this final step. For many businesses, the central core of what the business does is still profitable and so often directors will want to continue to trade. This is easily possible and a sale of assets can be arranged to a new company and a lease re-assigned by a landlord, which often leaves the new company trading on in the same line of work from the same premises.

Post from: Woodworking Training

How to wind up a carpentry company

A carpenter is a skilled crafts person who works with wood to construct buildings, furniture and many more objects. A person can gain the skill of Oxfordshire Carpentry through experience and study. There are many courses available for carpentry skills. These courses are designed to give you necessary theoretical and practical skills which are usually required to make a career in carpentry or wood occupation. The best part of these courses is that you don't need any previous experience. Here they will teach you how to use basic joints, inspect hatch and frame, erection and use of equipments and unloading and storage of sheet and timber materials. So a person who does these courses becomes a master in Carpentry.

When you are planning to make some changes in your home or office, you would always prefer a professional who can design and construct exactly what you need and as per your requirements. You will try and find the best Carpenter who is experienced in his field and can help you to design bespoke furniture and other requirements of your home. Other than the carpentry and joinery work, these carpenters will also help you in providing services for roofing, staircase installation, fitting wardrobes, window seats, wooden flooring, fitting cupboards and shelves, and many more things. So, carpentry trade is to be known as a combination of many things.

But it becomes difficult and stressful to find an experienced carpenter whose work you will like to appreciate. So, the main thing which you should do is to exactly describe what work you want to be done. Include the day the work should be started and the exact dimensions of the furniture incase to be made. Images or scans of photographs or plans help a lot in finding a perfect carpenter. This will save your time and money as the carpenter will know exactly what you need and will then contact you. You can then get different quotes from different Carpenters and choose the best tradesman quote from among the rest of the quotes depending on your requirements. Make your decision and pick up the best carpenter by checking out his reviews on previous carpentry or joinery jobs done by him. This will help you to know how neat and efficient he is in his job and whether you like his work or not. It all depends on the neatness of the work done and on the durability and strength of the work.

So, before you begin with any construction or any furniture work by a carpenter please check out these norms and then choose your Carpenter or Joiner. As a house cannot be constructed again and again and neither can you change its furniture often.

Post from: Woodworking Training

Carpentry in Oxfordshire

The primary advantage of using wood as a structural material in carpentry is the ease with which wood structural parts can be joined together with a wide variety of fasteners such as nails, spikes, screws, bolts, pins, staples and connectors of various types. Usually they all are made of metal, and most of all of iron.

For maximum rigidity and strength, each type of fastener calls for joint designs specifically adapted to the strength properties of wood being used and to dimensional changes that could occur with changes in moisture content (that is, unavoidable weather conditions) and wear and tear.

The following are the three most popular forms of fasteners in carpentry.

Nails

Nails are the most commonly used fasteners in construction. They are the carpenterâ??s most useful means of fastening structural parts. As such, a great variety of types and sizes is available to meet the demands of the carpentry industry. Size is crucial in selecting the right nails for the job. Diameter would be the first consideration. Short, thick nails typically loose quickly, whereas long, thin nails are more likely to break at the joints of the lumber. Basic rule is to use as long and as thin nail as will drive easily.

Some tips in determining which nail size is appropriate:

-          For lumber of medium hardness, the penny (head) of the nail should not be greater than the thickness of the board into which the nail is being driven.

-          Nails should be one penny smaller if used in hard woods.

-          When joining two boards together, the nail point should at least penetrate 1/4 inch of the far side of the second board.

-          The kind of wood is an essential factor in determining the size of nail as well. Soft woods may require nails that may be one penny larger, or sometimes, even two pennies larger.

However, all rules and tips are worth pennies compared to experience, as it is still the best guide in determining the appropriate nail size.

Screws

Wood screws are excellent alternatives to nails as carpentry fasteners.

They have worthwhile advantages over nails because they are sturdier. Also, it gives the carpenter more flexibility in adjusting the structure because of the ease in disassembling the joined parts. Just a twist with a screwdriver and itâ??s off! Unlike with nails, it is quite possible to damage the structure if itâ??s already been nailed together and you want to take it off. These advantages, however, also come at a cost since it takes more time and effort to install screws to structural materials than nails. With nails, you just need a hammer and just pound away. Screws are more tedious because of the need for more precision.

In the early days, most wood screws (probably 75 percent or more) used to be the flat-head type. This has changed however, with the emergence of the Phillips head screw in recent years.

Bolts

An alternative to both nails and screws are called bolts. These are used to bind parts tightly together where high strength is needed. A bolt is generally regarded as a rod having a head at one end and a threaded portion on the other to receive a nut. The nut is usually considered as forming a part of the bolt.

These fasteners are as essential to carpentry as the structural materials itself. Without them to hold parts together, functionality of the structure would be greatly compromised.

Post from: Woodworking Training

Keeping It Together in Carpentry

Carpenters are generally considered to be all-around and knowledgeable, if not skilled, in most facets of construction. They know a bit of masonry, tin smithery, and metal works. They are relied upon to erect scaffoldings. It is possible to be a rough carpenter and at the same time a finishing carpenter. They also make the floors, roofs, walls, and partitions and the necessary framing for items that do not require concrete. As a carpenter, one needs to be skilled at all kinds of tools, from manual to the portable and stationary power tools. Squares, hammers, and chisels are examples of manual tools. The power saw and drills are some of the power tools. One should also be able to read architectural plans, symbols, and construction drawings. Further, it is important to interpret them according to work specifications. Also, a good carpenter never underestimates the consequence of safety.

There are two main fields in carpentering, rough and finishing carpentry. Rough carpentry involves the unseen part of a house. This is the field that is actually involved in construction and building. Tradesmen in this field prepare formworks and bracings for reinforced concrete like columns, stairs, floors, walls, beams, girders, and, of course, for the footings and foundation. To form concrete structures, wooden formworks need to be strong and sturdy, but not too rigid in that it should take the weight of fresh concrete. Needless to say, the surface exposed to the concrete has to be clean and spotless. They also handle heavy framing for some structures that require hardy framing.

The work of finishing carpenters usually covers the visible areas and items that define the space. They produce drywall partitions, simple to complexly designed ceilings, moldings, manufacture and installation of doors and windows, flooring, counters, and cabinets. Doors, windows, and cabinetry have become specializations in themselves and have become distinct trades. When orders for the doors, windows, counters, and cabinets have arrived, it is they who finish the installation. Subjects in carpentry training comprise virtually all aspects of the craft, from materials, estimation, costing, to the tools and how to use them to create carpentry works.

Carpentry training is offered as a course by many colleges and institutions. Entering carpentry school at qualified training centers may have the slight advantage because it is more organized and certifications are handed out. Or it may be that a person is apprenticed to a skilled carpenter. Either way, exposure and adeptness in handling the material and the tools are keys to earning vocational qualifications from government certifying agencies. Training may also be done at home for the hobbyist and the weekend carpenter with do-it-yourself CDâ??s, videos, and e-books. Modules are available for simple projects, to repairs, how-toâ??s, and others. Most training programs cover everything from the ground up to the roof and everything in between including what needs to be done and how it is done.

Post from: Woodworking Training

Carpentry Training – For Budding Carpenters and Hobbyists

Carpentry Tools

Carpenters use various special tools to carry out their job. These tools are categorized into hand tools and power tools. Most often carpenter uses hand tools for carrying out simple or even complex jobs. Power tools are used when working with heavy wood or large amount of work is to be done. Some very popular tools used for carpentry are mallets, hammers, chisels, saws, file, clamp, pliers, punches and measuring tapes.

Some useful tips about Carpentry

A carpentry job may include many small functions as part of a big project. These functions include measuring, marking, cutting, sawing, striking, chiselling, checking, boring, lengthening, sharpening and framing of joints.

Cut once after measuring twice, this is the most important rule of the carpenters who believe in making perfect objects in perfect time. This is why measuring tape and 90 degree angled tool are among the most important tools for carpenters. An end product is always perfect if you measure right and cut materials perfectly. A square is used for drawing straight lines and measuring tapes give you right measurements.

Simple saw is the best choice for cutting wood in straight lines, especially for the beginners. Coping saw is used for cutting curves. But for beginners, it is not recommended to use electric saws and cutters as they may injure themselves. Even if you are using it, you must read all the instructions carefully, about its usage.

Drill machines are the perfect carpentry tools to make holes in walls and wood. These are the power operated tools which make the job very easy and less laborious. Various kinds of nails and glue are the other elements you would need for any kind of carpentry job. Nailing requires skill which a person learns with practice. A beginner can start making simple things like bookshelves, simple tables, closet fixtures, etc.

While going for a project, choose the wood carefully. Measure and mark it even more carefully. If you have drawn some wrong marking, make a cross sign over it to differentiate it from the other lines. Job of carpenter involves too much precision without which you cannot make a perfect product.

After you have chosen an object and the appropriate wood for it, you can start your first carpentry project. Measuring is important for making a perfect carpentry object. So measure you wood twice according to the pattern before cutting it. Mark them with pencil and cross out the lines drawn by mistake. After you have cut wood pieces, it is time to put them together. Use nails and screws and according to the thickness of your wood, they should not stick out of the wood. Along with nails, you can use wood glue as well to make the joint stronger.

Post from: Woodworking Training

Carpentry: Tools and Tips

In general construction, it is the carpenters that have the highest demand and are, thus, the most in numbers than others. In many areas, carpenters are able to do the job by themselves. Wood work has the highest rate of actual activity, from formworks for concrete, to framing, interior wood pieces, flooring, and roofing. Highly-proficient, well-rounded and adept carpenters with a good range of skills are sought after, so it is always best to re-train and polish the skills already in their repertoire and add more abilities when in-between jobs.

Carpentering in construction covers many areas. In pre-construction work, there is rough carpentry, formworks preparation and construction, erection of scaffolding, bracing, temporary structures, and sizing and materials estimation among others. In the actual construction, the carpenter is usually the lead in making frames, roof trusses, floor construction, insulation, walls and partitions, roof construction, decks, finishing, and connecting and joinery among others. In the finishing stages, carpenters are called in to add moldings, cornices, and decoration to interior spaces. Outside of construction, a lot of carpenters are making doors, windows, furniture, counters, and cabinets. In addition to the listed, there will always be lead and assisting carpenters especially in big projects.

There are a number of good search resources for carpentry jobs at local job postings in your area and in the Internet. But since they require highly skilled, well-rounded and experienced carpenters, they look for individuals who have undergone reasonable carpentry schooling. Many carpentry schools provide practical, in-depth and very competitive training modules. They expose their trainees to environments and situations that are comparable to actual job conditions. They are considered as more able to perform their work as compared to simple skilled tradesmen who have simply picked-up carpentering knowledge while on the job.

Contractors also keep an eye on desirable physical and attributes for incoming carpenters applying in their companies. Dexterous, nimble, physically fit, good hand and eye coordination, and the ability to mentally perform quick and accurate mathematical calculations and conversions are sought-after. Every bit of information should be stated in a resume. Most wood smiths finished only high school education and from there attended vocational schools. It will be advantageous to highlight everything related to carpentry in and outside of school. If for example, they include basic carpentry workshops, basic schematic sketches and drawings, and the like.

Post from: Woodworking Training

Knowing the Right Carpentry Jobs

Courses are made as an introduction to carpentry up to the virtuosity levels. It starts out from the basics of woodworking up to integration of other complemental trades, covering carpentry works for building foundation, to framing, to walls, up to the roof and everything else inside. All courses require their trainees to wear safety overalls, steel-capped shoes or boots, safety goggles, and proper headgear. Classroom courses, or those that are not hands-on activities, teaches trainees basic industrial skills. Also, pointers are given on how to identify and handle the different kinds of woods.

Trainees are taught pre-technical courses ranging from basic arithmetic, conversion of units from English to metric and vice versa, understanding fractions and angles, taking measurements, safety in the workplace, reading of schematics and drawings, employment practices, and working with chemicals among others. In measurements, trainees are taught how to quantify with flexible and rigid rules and tapes, get the perimeter of rooms and objects, know its area, calculating for circumferences, and others. Workplace safety covers working with chemicals, fire hazards, electrical hazards, accident prevention, and hazardous wastes. To accurately read drawings and schematics, trainees are introduced to proper reading and interpretation of standard symbols, dimensions, electrical layouts and symbols, piping layout and symbols, welding standard symbols, drawing scales, interpreting the different types of lines and how they are drawn, electronics drawings, and how to produce sketches.

Comprehensive carpentry training courses should always include the basics. There would be no wood smith without his tools and the know-how to take care of them. Courses on the many types of tools are discussed such as the power tools as well as manual tools since a carpenter would require the use of these types on a single project. How to maintain them are taught as well. The electric drilling tool is perhaps the most widely used power tool in carpentry. It is used to make holes in masonry, concrete, and wood. The electric grinder is used for shaping and finishing. Of the power cutting tools, the portable variety is most used in job sites than the stationary. The stationary types are normally used in the wood mills.

Power tools offer ease and convenience not available before in manual tools. Power sanders make it easy to finish and prepare a surface for painting. Power routers enable carpenters to make irregular shapes and contours. The pneumatic hammer makes fixing two parts together easier with one strike compared to the traditional hammer. The traditional hand tools, on other hand, offer control not available in the power tools. From how to use the handsaw, hammer, drill, planes, and chisels, the trainee will know that hand tools are still a part of carpentry.

In the actual carpentry training courses, trainees will be exposed in construction materials; types of frames and framing methods; joints and connections; wall and partition construction; roof construction; stair construction; metal works; rough carpentry as for formworks, supports, and bracings; constructing decks; making arches; doors and windows; insulation and acoustic control; beams and joists; floor construction; and architectural finishing, moldings, cornices, and painting.

Post from: Woodworking Training

Carpentry Training Courses – Increasing Skill Levels and Income

Carpenters are generally considered to be all-around and knowledgeable, if not skilled, in most facets of construction. They know a bit of masonry, tin smithery, and metal works. They are relied upon to erect scaffoldings. It is possible to be a rough carpenter and at the same time a finishing carpenter. They also make the floors, roofs, walls, and partitions and the necessary framing for items that do not require concrete. As a carpenter, one needs to be skilled at all kinds of tools, from manual to the portable and stationary power tools. Squares, hammers, and chisels are examples of manual tools. The power saw and drills are some of the power tools. One should also be able to read architectural plans, symbols, and construction drawings. Further, it is important to interpret them according to work specifications. Also, a good carpenter never underestimates the consequence of safety.

There are two main fields in carpentering, rough and finishing carpentry. Rough carpentry involves the unseen part of a house. This is the field that is actually involved in construction and building. Tradesmen in this field prepare formworks and bracings for reinforced concrete like columns, stairs, floors, walls, beams, girders, and, of course, for the footings and foundation. To form concrete structures, wooden formworks need to be strong and sturdy, but not too rigid in that it should take the weight of fresh concrete. Needless to say, the surface exposed to the concrete has to be clean and spotless. They also handle heavy framing for some structures that require hardy framing.

The work of finishing carpenters usually covers the visible areas and items that define the space. They produce drywall partitions, simple to complexly designed ceilings, moldings, manufacture and installation of doors and windows, flooring, counters, and cabinets. Doors, windows, and cabinetry have become specializations in themselves and have become distinct trades. When orders for the doors, windows, counters, and cabinets have arrived, it is they who finish the installation. Subjects in carpentry training comprise virtually all aspects of the craft, from materials, estimation, costing, to the tools and how to use them to create carpentry works.

Carpentry training is offered as a course by many colleges and institutions. Entering carpentry school at qualified training centers may have the slight advantage because it is more organized and certifications are handed out. Or it may be that a person is apprenticed to a skilled carpenter. Either way, exposure and adeptness in handling the material and the tools are keys to earning vocational qualifications from government certifying agencies. Training may also be done at home for the hobbyist and the weekend carpenter with do-it-yourself CD's, videos, and e-books. Modules are available for simple projects, to repairs, how-to's, and others. Most training programs cover everything from the ground up to the roof and everything in between including what needs to be done and how it is done.

Post from: Woodworking Training

Carpentry Training – For Budding Carpenters and Hobbyists

This report provides key data and concise analyses, presents a comparative analysis on the development of Buildersâ?? Carpentry & Joinery industry in 31 provincial regions and 20 major cities in visualized form of data map. As shown in this report, the major distribution areas of Buildersâ?? Carpentry & Joinery industry in China are Zhejiang, Liaoning and Jilin provinces. More than 140 above sized enterprises located in Zhejiang province with total sales of US$ 1,700 million. ( http://www.bharatbook.com/detail.asp?id=132221&rt=China-Builders-Carpentry-Joinery-Industry-Profile-ISIC2022.html )

The report also includes a list of top 100 enterprises in the sector and the comparison on investment environment in top 10 hot regions in China. In addition, the report truly reflects the position of foreign enterprises in this industry across China based on a comprehensive comparison of operating conditions among different enterprise types.

Furthermore, this is the first report to adopt ISIC (International Standard Industrial Classification of All Economic Activities) in classification of Chinese enterprises, corresponding to the reading habit of international readers, and it is also very helpful for readers to make a comparison on the development condition and investment potential of Buildersâ?? Carpentry & Joinery industry in China with that in other countries.  The report directly shows the difference in various regions of Mainland China in terms of Buildersâ?? Carpentry & Joinery industry, providing an important reference for investors' selection of target regions to make investment.

In this report, readers will get:

â?¢ A comprehensive picture on distribution of and difference in performance in regions of Mainland China in terms of the Buildersâ?? Carpentry & Joinery industry;
â?¢ To figure out the hot regions in China for Buildersâ?? Carpentry & Joinery industry, find out the potential provinces and cities suitable for investment as well as the economic development level and investment environment in these regions;
â?¢ A clear picture on the overall development, industry size and growth trend of Buildersâ?? Carpentry & Joinery industry across China;
â?¢ A clear picture on development status of foreign enterprises, state-owned enterprises, and private enterprises in recent years as well as the industry position of the above ownerships;
â?¢ Based on adoption of the global uniform industry classification standard - ISIC, the report enables readers to make a direct comparison of China Buildersâ?? Carpentry & Joinery industry with parallel industry in other countries;
â?¢ Present readers with a list of top 100 enterprises inside the industry in terms of the sales revenue;
 

To know more and to buy a copy of your report feel free to visit : http://www.bharatbook.com/detail.asp?id=132221&rt=China-Builders-Carpentry-Joinery-Industry-Profile-ISIC2022.html

Or

Contact us at :

Bharat Book Bureau
Tel: +91 22 27578668
Fax: +91 22 27579131
Email: info@bharatbook.com
Website: www.bharatbook.com
Blog: http://bharatbookresearch.blogspot.com
Follow us on twitter: http://twitter.com/3bbharatbook
 

Post from: Woodworking Training

China Builders Carpentry & Joinery Industry Profile

Additionally, the report directly shows the difference in various regions of Mainland China in terms of builders' carpentry & joinery industry, providing an important reference for investors' selection of target regions to make investment.

What will you get from this report?

- To get a comprehensive picture on distribution of and difference in performance in regions of Mainland China in terms of the builders' carpentry & joinery industry;

- To figure out the hot regions in China for builders' carpentry & joinery industry, find out the potential provinces and cities suitable for investment as well as the economic development level and investment environment in these regions;

- To get a clear picture on the overall development, industry size and growth trend of builders' carpentry & joinery industry across China in the past 3 years;

- To get a clear picture on development status of foreign enterprises, state-owned enterprises, and private enterprises in recent years as well as the industry position of the above ownerships;

- Based on adoption of the global uniform industry classification standard - ISIC, the report enables you to make a direct comparison of China builders' carpentry & joinery industry with parallel industry in other countries;

- Present you with a list of top 100 enterprises inside the industry in terms of the sales revenue;

Industry Definition:

Builders' Carpentry & Joinery: Manufacture of builders' carpentry and joinery (ISIC: 2022)
ISIC 20: Manufacture of wood and of products of wood and cork, except furniture; manufacture of articles of straw and plaiting materials
ISIC Code: International Standard Industrial Classification of All Economic Activities (ISIC), Revision 3.

Regions Covered By This Report:

- All the 31 provincial regions in Mainland China;
- Top 20 Chinese cities in terms of builders' carpentry & joinery industry.

Enterprise Types Covered By This Report:

- Top 100 enterprises;
- Enterprises Funded by Foreign Countries (territories), Hong Kong, Macau and Taiwan;
- Chinese State-owned Enterprises;
- Collective-owned Enterprises;
- Cooperative Enterprises;
- Joint-Equity Enterprises;
- Private Enterprises.

Key Statistic Indicators Covered By This Report:

- Industrial Output
- Number Of Employees
- Enterprise Number
- Sales Revenue
- Profits
- Rate Of Return On Sales
- Rate Of Return On Assets
- Rate Of Return On Net Assets
- Number Of Enterprises In Red
- Range Of Loss
- Total Losses
- Percentage Of Foreign-Funded And HK-, Macau-, Taiwan-Funded Enterprises In Terms Of The Sales Revenue
- Percentage Of Foreign-Funded Enterprises In All Foreign-Funded Enterprises And HK-, Macau-, Taiwan-Funded Enterprises In Terms Of The Sales Revenue
- GDP
- Growth Rate Of GDP
- GDP Per Capita
- Growth Rate Of GDP Per Capita
- Growth Rate Of The Added Value Of Primary Industry
- Growth Rate Of The Added Value Of Secondary Industry
- Growth Rate Of The Added Value Of The Tertiary Industry
- Industrial Value-Added Of Enterprises Above Designated Size
- Growth Rate Of Industrial Value-Added Of Enterprises Above Designated Size
- Industrial Products Sales Rate Of Enterprises Above Designated Size
- Growth Rate Of Industrial Value-Added Of Foreign-, And HK-, Macau-, Taiwan-Funded Enterprises
- Investment On Fixed-Assets
- Growth Rate Of Investment On Fixed-Assets
- Total Retail Sales Of Consumer Goods
- Growth Rate Of Total Retail Sales Of Consumer Goods
- Total Import & Export
- Growth Rate Of Total Import & Export
- Realized Foreign Direct Investment
- Growth Rate Of Realized Foreign Direct Investment
- CPI
- PPI
- RMPPI
- Urban Per Capita Disposable Income
- Rural Per-Capita Net Income
- Freight Mileage
- Growth Rate Of Freight Mileage
- Port Cargo Throughput
- Growth Rate Of Port Cargo Throughput
- Resident Population

For more information please visit:

http://www.aarkstore.com/reports/China-Builders-Carpentry-Joinery-Industry-Profile-ISIC2022-40493.html

PH.NO. 919272852585

Post from: Woodworking Training

China Builders’ Carpentry & Joinery Industry Profile – ISIC2022-Aarkstore Enterprise

Many carpenters simply pick up their skills on the job. However, this kind of training could lead to lack of knowledge in some areas. Needless to say, this is not a good point to put on a resume for employers to see. The truth is that contractors prefer carpenters who underwent apprenticeship under a master carpenter or attended a recognized trade school. This assures them that carpenters have experienced comprehensive training in all aspects of carpentry and have ample exposure to environments similar to actual job conditions. The construction industry is actually in needing of apprenticed carpenters. Less than half of the total carpenters have attended trade school.

There is no alternative for receiving training in a formal way. Carpentry schools teach everything there is to know about on the craft. It takes about six to ten weeks, to one year or longer to finish a course that follows a specific schedule, depending on the courses taken. Before one can complete a course, proficiency, knowledge, and hands-on skills are assessed and graded. Trainees are closely guided. Trade school courses feature classroom instruction in the beginner pre-technical phase. Basics of manual and power tools, working with materials, work site safety, basic arithmetic, conversion skills, measuring techniques, materials and cost estimation, employment practices, accident prevention and first-aid, and interpretation of drawings and schematics are taught. From the basics, they guide their students in the application of those subjects in the actual carpentry training. This course teaches students technical skills in preparation of materials and construction.

One positive aspect about trade schools is the emphasis on safety. Early on, trainees are taught of its importance and are required to put on safety clothing before proceeding. Often, trade schools provide for the tools and materials to be used. Hands-on involvement and participation is required throughout the entire training period. Completion certificates are handed out as well as a portfolio of the trainee’s work for further reference. These can be used when applying for a job. Longer courses may include vocational qualifying certificates from related government regulatory agencies. Some schools welcome former trainees and accommodate inquiries and clarifications regarding the carpentry work they are currently engaged in.

Many carpentry schools are borne out of the need to provide quality training and employment for individuals who could not go to college or even finish high school education. Generally, they aim to introduce employable skills and develop positive social values. Courses cover presentation and discussion of theories in the classroom and practical instructions in workshops. Trade schools slightly differ from one another with regards to their specialty. Many offer courses in general carpentry. Others specialize in cabinet technology and construction management. Not a few are in the field of building construction and construction technology. Some have made their name in furniture making. Others are noted for quality training in home repair, remodeling, and restoration.

Post from: Woodworking Training

Hands-On Learning in a Carpentry School

Courses are made as an introduction to carpentry up to the virtuosity levels. It starts out from the basics of woodworking up to integration of other complemental trades, covering carpentry works for building foundation, to framing, to walls, up to the roof and everything else inside. All courses require their trainees to wear safety overalls, steel-capped shoes or boots, safety goggles, and proper headgear. Classroom courses, or those that are not hands-on activities, teaches trainees basic industrial skills. Also, pointers are given on how to identify and handle the different kinds of woods.

Trainees are taught pre-technical courses ranging from basic arithmetic, conversion of units from English to metric and vice versa, understanding fractions and angles, taking measurements, safety in the workplace, reading of schematics and drawings, employment practices, and working with chemicals among others. In measurements, trainees are taught how to quantify with flexible and rigid rules and tapes, get the perimeter of rooms and objects, know its area, calculating for circumferences, and others. Workplace safety covers working with chemicals, fire hazards, electrical hazards, accident prevention, and hazardous wastes. To accurately read drawings and schematics, trainees are introduced to proper reading and interpretation of standard symbols, dimensions, electrical layouts and symbols, piping layout and symbols, welding standard symbols, drawing scales, interpreting the different types of lines and how they are drawn, electronics drawings, and how to produce sketches.

Comprehensive carpentry training courses should always include the basics. There would be no wood smith without his tools and the know-how to take care of them. Courses on the many types of tools are discussed such as the power tools as well as manual tools since a carpenter would require the use of these types on a single project. How to maintain them are taught as well. The electric drilling tool is perhaps the most widely used power tool in carpentry. It is used to make holes in masonry, concrete, and wood. The electric grinder is used for shaping and finishing. Of the power cutting tools, the portable variety is most used in job sites than the stationary. The stationary types are normally used in the wood mills.

Power tools offer ease and convenience not available before in manual tools. Power sanders make it easy to finish and prepare a surface for painting. Power routers enable carpenters to make irregular shapes and contours. The pneumatic hammer makes fixing two parts together easier with one strike compared to the traditional hammer. The traditional hand tools, on other hand, offer control not available in the power tools. From how to use the handsaw, hammer, drill, planes, and chisels, the trainee will know that hand tools are still a part of carpentry.

In the actual carpentry training courses, trainees will be exposed in construction materials; types of frames and framing methods; joints and connections; wall and partition construction; roof construction; stair construction; metal works; rough carpentry as for formworks, supports, and bracings; constructing decks; making arches; doors and windows; insulation and acoustic control; beams and joists; floor construction; and architectural finishing, moldings, cornices, and painting.

Post from: Woodworking Training

Carpentry Training Courses – Increasing Skill Levels and Income

Basic carpentry skills are needed to properly carry out home repairs, minor additions, renovations, and other projects. Trade schools that teach the basics of carpentering normally discuss about introductory courses such as the manual and power tools and how to use them, read and interpret drawings and symbols, how to mark and measure, executing small projects, basic principles, and practical carpentry skills. Tutorial videos and e-books are also available to the weekend carpenter. Joinery works are some of the basic skills. From the very simple glued joint, to the half joints, the angular mitred joints, the dovetail, mortise and tenon, and others. A mark of a good carpenter knows which joint to use on a particular project.

Carpentry is a complex undertaking that only professional carpenters can perform. Simple carpentry works that are mostly confined to drilling, nailing, and fixing need only the basic tools. One would only depend on simple manual hand and power tools. These tools are steel framing squares, tape measures, handy power nailers, some chisels, chalk line, an electric drill, retractable utility knife, extension cords for power tools, a ladder, power cutters, circular saw, hardware, accessories, and others. Safety goggles, hand gloves, and steel-capped boots cover the safety end. All these items for light construction can fit in carpenter kits and light trucks one can bring along in going to job sites.

Simple carpentry may be called light carpentry in that the size of the work can be managed by one or three people at most. And nearly all of these are related to carpentry jobs in homes, establishments, and interior works. They cover the work of constructing dry walls, fitting of door linings, cutting and fixing of architraves and skirting, dado rails, moldings, windows, kennels, play houses, and others. The proper handling of wood is basic at the same time very important to avoid wastage. Choosing the right kind of wood is also one of the basics. There are many types of wood, from soft to hardwood, that are chosen for work-specific purposes.

A basic carpentry course is a good start on the way to being a master carpenter. Probably the most practical and integral part of it is to accurately read and interpret architectural plans and schematic drawings and make functional multi-view sketches for actual execution. If one canâ??t correctly tell what and how the job entails and where, no matter his adeptness at his tools, then the individual is as good as a warehouseman. One very important facet is the understanding of electrical layouts and symbols to avoid electrical hazards and accidents. Proper analysis of drawing scales and transferring them to the job site is as important as knowing what the types of lines and their weights mean. There are numerous types of lines used in drawings that signify that something else is either above, below, or hidden.

Post from: Woodworking Training

Basic Carpentry – On the Way to the Top

Basic carpentry skills are needed to properly carry out home repairs, minor additions, renovations, and other projects. Trade schools that teach the basics of carpentering normally discuss about introductory courses such as the manual and power tools and how to use them, read and interpret drawings and symbols, how to mark and measure, executing small projects, basic principles, and practical carpentry skills. Tutorial videos and e-books are also available to the weekend carpenter. Joinery works are some of the basic skills. From the very simple glued joint, to the half joints, the angular mitred joints, the dovetail, mortise and tenon, and others. A mark of a good carpenter knows which joint to use on a particular project.

Carpentry is a complex undertaking that only professional carpenters can perform. Simple carpentry works that are mostly confined to drilling, nailing, and fixing need only the basic tools. One would only depend on simple manual hand and power tools. These tools are steel framing squares, tape measures, handy power nailers, some chisels, chalk line, an electric drill, retractable utility knife, extension cords for power tools, a ladder, power cutters, circular saw, hardware, accessories, and others. Safety goggles, hand gloves, and steel-capped boots cover the safety end. All these items for light construction can fit in carpenter kits and light trucks one can bring along in going to job sites.

Simple carpentry may be called light carpentry in that the size of the work can be managed by one or three people at most. And nearly all of these are related to carpentry jobs in homes, establishments, and interior works. They cover the work of constructing dry walls, fitting of door linings, cutting and fixing of architraves and skirting, dado rails, moldings, windows, kennels, play houses, and others. The proper handling of wood is basic at the same time very important to avoid wastage. Choosing the right kind of wood is also one of the basics. There are many types of wood, from soft to hardwood, that are chosen for work-specific purposes.

A basic carpentry course is a good start on the way to being a master carpenter. Probably the most practical and integral part of it is to accurately read and interpret architectural plans and schematic drawings and make functional multi-view sketches for actual execution. If one can't correctly tell what and how the job entails and where, no matter his adeptness at his tools, then the individual is as good as a warehouseman. One very important facet is the understanding of electrical layouts and symbols to avoid electrical hazards and accidents. Proper analysis of drawing scales and transferring them to the job site is as important as knowing what the types of lines and their weights mean. There are numerous types of lines used in drawings that signify that something else is either above, below, or hidden.

Post from: Woodworking Training

Basic Carpentry – On the Way to the Top

Post from: Woodworking Training

Basic Carpentry

Finish carpentry: here the carpenter will specialize in furniture making, fine wood work, instrument making etc.

Trim carpentry: this carpentry specializes in moulding and trims such as mantels, baseboards, window and door casting.

Ship carpentry: this branch of carpentry specializes in ship building, its maintenance and repair methods and other carpentry specific to nautical needs.

Scenic carpentry: this branch of carpentry specializes in film making and the construction of sets, scenery and theatre builds.

Since carpentry is a skilled profession it is but obvious that it would need specific tools .The tools that are used in carpentry can be broadly classified into the following types:

STRIKING TOOLS

1. Tools that are used for striking only, as Hammers and Mallets

2. Tools that are used for striking and cutting, as Hatchets, Axes, Adzes, etc.

RASPING TOOLS OR TOOLS THAT ACT BY ABRASION

1. Saws of all kinds, for cutting wood.

2. Rasps and Files, for smoothing, shaping, cutting, etc.

PARING TOOLS OF ALL KINDS

1. Planes of various kinds, for smoothing, moulding, etc.

2. Spoke shaves and Drawing-knives.

3. Chisels and Gouges.

BORING TOOLS

1. Bradawls, Gimlets, and Augers.

2. Brace and Bit, sometimes called Stock and Bit.

HOLDING OR GRASPING TOOLS

1. Pincers and Pliers, Nippers, Spanners, and Wrenches.

2. The Vice, including Hand-vice, Bench Vice, etc.

TOOLS OF GUIDANCE AND DIRECTION

1. The Carpenter's Rule and Chalk Line.

2. The Square, Bevel, Gauge, Mortising Gauge, MITRE-Box.

3. Spirit Level, Straight Edge, Plumb and Level.

4. Compasses and Calipers.

MISCELLANEOUS TOOLS NOT SUBJECT TO CLASSIFICATION.

Screwdriver, Nail-Punch, Scriber, Reamer, etc.

With such a lot of tools, it is evident that carpentry is not something which everyone can do without getting trained in it formally.

http://www.balhambuilder.co.uk

Post from: Woodworking Training

Various Types and Tools in Carpentry

 First, when doing finish carpentry work, your attitude and mood directly affects your performance and quality of the trim work. Some of the best finish carpenters have a difficult time doing quality work if they are upset or mad or depressed about something in their life. To prevent this, in the morning before you begin working, take a shower, eat breakfast, put on some new shoes, have a clear mind, be in a fantastic mood and you will be surprised at what you can accomplish. Focus is the key. Having the right tools for the project is also a huge factor for quality. Poor tools can some times produce poor quality. Poor tools can fuel aggravation. So be sure to buy or borrow the best tools you can. Make sure the saws have sharp blades, keep your pencil sharp, your knife sharp and your mind sharp and your work will be sharp. Remember - success doesn't come to you, you go to it.

 Knowing how to use these tools safely and effectively is also a big factor. Practice a while with them before working with them if you are not familiar with them.  Practice making some angle cuts that are involved with trim work. All the different joints and miters can be a bit of a challenge at first - so practice making miters or coping or doing outside corners before cutting and installing the actual pieces. Practice with the different trim pieces like the casing or baseboard or shoe or chair rail whatever the job entails. Practice makes perfect.

 Another factor that can distract you is the environment you are working in. Interruptions like too many people around or in the way, interrupting phone calls, working where it is cold or hot or what ever the case, all of these should be addressed before you begin. Do your best to make it as comfortable as possible. When you get to your working area clean it up and do what you can to keep it clean and clutter free. Walking over wood scraps and cords and hoses is not only annoying but also dangerous.  I once tripped over a hose with my hands full and fell to the floor. I caught my self with one hand hitting the floor and fractured my wrist. The best part is that I am indestructible and that sort of thing never happens to me....Yea Right! 

Your goal is to make it as comfortable and as safe as you can any way you can, given the situation. Even after taking all of these suggestions into consideration this work can still try your patience. There may be times when no matter how hard you try you can't make something work.  When this happens, take a break, clean up, or go start something different, chances are when you come back it will work.  Remember this, wisdom and experience doesn't come without a little suffering and rarely do we experience success without practice. If you take the time to prepare both mentally and with your technique, you will end up with a finished project you can be proud of. 

Post from: Woodworking Training

Getting the Mind Set for Finish Carpentry

Trim wood should be acclimated to the inside environment of the house where it will be installed. This does also apply to the wood of a new wood floor to be installed. What this means exactly is the wood needs time to adjust to the temperature and humidity levels of the house where it will be installed. This in turn reduces the shrinkage of the wood and that helps to keep miters tight and doors working properly. There is much discussion on how long this acclimation period should be and a few variables do come into play here especially with a newly built home. A very minimum of an acclimation period would be 48 hrs. if the environment change of the storage place of the trim wood or the store to the house environment is not a huge difference. Another factor is after the acclimation period it is best to get the wood finished and sealed whether you do it before or after installation.

Ultimately wood is going to shrink and swell according to the seasons. Some places more than others due to the climate differences. The best way to reduce this is to try and keep the environment in the house relatively even with just the temperature although I have seen a new house with new trim work sitting empty with no activity like cooking or showering for a long period of time have major shrinkage in the trim wood due to no humidity. I had trimmed this house and was just sick when I went back for the final; fortunately the builder that I had done the work for understood this problem and took full responsibility. I had been in the finish carpentry business for a long time and had a good reputation of doing good work but some times that reputation doesn’t mean anything to the people that don’t understand these problems.

For the do it yourselfers doing trim work, there are a few things to consider. If you are remodeling or doing renovations to an existing home just simply taking the precautionary measure of acclimating the wood will eliminate the major shrinkage problem in most cases. On new homes it is however nice to know the humidity levels in the house as well as the wood. One easy way to check the wood is with a moisture meter tester. This little meter is relatively cheap or can be borrowed from a contractor that does building or remodeling. The use of a dehumidifier is recommended in a new house or new construction and doing a little research for the moisture content that is recommended for the area that you live in is also advisable. This is due to the different climates in the country and various temperature changes for the different areas. As a finish carpenter it is important for people to understand some of these issues concerned with wood shrinkage whether you are doing the work yourself or hiring a professional to do the work for you ultimately to protect yourself.

Post from: Woodworking Training

Understanding Wood Shrinkage in Finish Carpentry

Sometimes this trim wood is referred to as molding. This decorative trim wood or moldings come in many types of wood and is not limited to any type of wood. Some of the most common are oak, maple, birch, mahogany, cherry, pine, hickory, walnut and so on. These moldings can also be made of man made materials like high-density polymers. This trim wood or moldings can also be purchased in raw form or even prefinished form. 

This trim wood comes in a wide variety of styles also. Some of the most common styles include ranch style, colonial style, Princeton style (which is close to colonial), Victorian style and so on. You could even create your own style. Some places you may see a home made style is in cabins or lake homes. One thing to keep in mind when choosing your style and this is just a suggestion is to stick with one style throughout for conformity although not necessary. 

These different styles also come in different sizes. Some times in the older Victorian houses the trim wood is quite big. For example, let's say baseboard is commonly around 3" in height (at least in a lot of the newer homes) and in the older Victorian homes it can be as tall as 6" or more in height. This applies to the door and window trim also in these older homes, they liked it big. They not only liked it big but also very decorative. 

One of the next choices would be how this trim wood is to be finished. By this I mean the color of the stain or if it would be painted. If the trim wood is painted you would not need to go with the more expensive hard woods for your trim. Paint grade trim can be for example pine and is much less expensive and going this route of painted trim would cost considerably less especially if you are doing the painting on your own.  

So with all of these choices regarding finish carpentry no matter what is chosen it serves a number of functionalities, adds beauty, and you will have your own distinctive style.  After all the decisions, the installation process is next. If you elect to do your own finish carpentry I have found it to be very very rewarding work how ever it does take a little practice and patience. If you have access to all the right tools for the job and the time, it is well worth doing it yourself and saving yourself a bundle of money. There are plenty of instructions and a lot of good information with tips and tricks on the web to be able to pick up this unique craft without too much trouble without having to be an actual carpenter.  

Post from: Woodworking Training

Finish Carpentry Choices

Finish carpentry is one of the projects more and more people are doing on their own. A few reasons for this are because of money or the lack of money, or because of the availability of all the information that is accessible. Some times even with all the information through books, videos, or the web people still have trouble with finish carpentry. Some reasons for this is because it is a type of craft that requires actually doing it and learning the different variables and problems involved with for example, hanging doors or just every time a stick of trim wood goes up. Some of these variables may include crooked floors, crooked walls, crooked framing or maybe even something like extra wide jambs. Here I am going to give some advice and tips to help explain some of these variables and problems you might encounter while doing your own finish carpentry.

Hanging Doors

I have found that casing my doors on one side before installing the doors makes it much quicker and easier in most cases. This of course does not hold true every time but for the most part it does. Be sure to case the side which goes to the inside of the room. To make it even quicker some times you can order or buy these doors precased on one side straight from the factory, store or lumber yard.

Casing doors or windows

.One common problem when applying casing to a door or window is the jamb does not come out flush with the sheetrock of the interior wall. This is particularly true on outside doors or garage doors. One way to remedy this is to take your hammer and hammer down or crunch the sheetrock down next to the jamb. Be careful as to not damage the sheetrock out past what your trim will cover. If you do, it can be fixed with a little spackle or sheetrock mud but try to avoid this. The idea here is to get the casing as flat against the wall as possible so it is not tipped in toward the jamb. The more it is tipped the harder it is to get nice mitered corners.

For casing windows for the first time

With windows sometimes curtains or window dressings will cover up the trim. Start in the bedrooms or back rooms first or where you think there may be curtains. Casing windows does take a little practice and patience so take your time with the miters. Try to keep your reveal as uniform as possible but if you do need to fudge it a little to tighten up a miter that is ok as long as its just a tiny adjustment. The reveal is not as eye catching as a loose miter. If you look at trim work in restaurants and businesses and other homes you will see a huge variety of the quality of work. Some of the quality is really nice and some is so bad you wonder how it passed. I can almost guarantee yours won’t be absolutely perfect every time so know your tolerances and what your expectations are that you will except from yourself. A good trimmer knows his tolerances well.

Using hardwoods

When using hardwoods such as oak or maple or whatever stay away from knots in the wood when nailing. If you shoot a nail in near a knot you risk splitting the wood. These hardwoods will undoubtedly split on you at one point or another. If the wood splits it can be filled with wood filler if it’s not split to bad and would look just fine. If by chance a piece ends up splitting right off it can be glued and clamped back together without to much trouble and again would look ok. If possible use this piece in an area that is not noticeable such as inside a closet or back side of a bedroom door or some where it wouldn’t be highly noticeable. Keep in mind almost everything can be fixed.

Match your Wood

Let’s say for example oak. The wood grains and color of oak can vary quite a bit so match your trim wood ahead of time for a good uniform look in your work. For the pieces that don't match use them in closets and less conspicuous places or places only you will see like the laundry room, again just not in highly visible places. This applies to all other varieties of wood also not just oak.

Perfect measurements

In finish carpentry to obtain those perfect measurements, set the wood in place and mark the wood. It’s quicker and much more accurate then using a tape measure for the precise cuts at joints and miters. I only use my tape when it is necessary. This is particularly true when applying casing. Very precise cuts are necessary and essential at times.

By using some of these suggestions your trim work will undoubtedly be more professional looking and at the same time may save you some aggravation. A few things to keep in mind while you are working on your project, nothing is  absolutely perfect. Wood filler can and will fix some of the problems encountered. Know what your tolerances are, in other words know what is acceptable of yourself.

Post from: Woodworking Training

Helpful Finish Carpentry Tips, Tricks and Information

In finish carpentry the trim wood around doors is called casing. When casing a door you want to try and get the miters as tight as possible.  A miter joint is the point where two pieces of casing meet at a corner. At a 90 degree corner where two pieces of casing meet each piece will be cut at 45 degrees to make this 90 degree corner. In theory this should work perfectly every time but little variables and imperfections throw this theory out of whack. Here are some tips and tricks to use to combat these little variables for almost perfect miters every time.

In order to have two pieces of casing cut at 45 degrees to make a 90 degree corner the casing has to be perfectly flat. A lot of times this isn't possible because the jamb of a door either sticks out past the inside sheet rocked wall or doesn't come out flush to the inside sheet rocked wall. This causes the casing to be tipped either inward or outward and when the casing is tipped in or out this will change the degree at the corner because of the distance of the miter to close the gaps. For example; if the casing is tipped inward or outward the miter will be open slightly to the inside or outside of the joint depending on how much it is tipped. Chances are you will run into this problem while doing finish carpentry but there is a solution.

In finish carpentry when casing a door or window always start with the top piece of casing. If the casing will be fairly flat when applied in place go ahead and cut each end at 45 degrees with a slight bevel back at the cut so the face of the casing is just slightly longer then the back of the casing. To get this slight bevel at the 45 degree cut slide a small piece of card board under the casing and close to the blade before cutting to slightly lift the end of the casing up the thickness of the card board. This piece of card board should be about an inch or so wide and the length of the width of the casing.

Another technique to get this bevel is to cut the casing upside down at the saw. If you have traditional type casing the casing will be thicker on the outside edge and go thinner to the inside edge. By cutting the casing upside down you automatically will create a natural back cut or bevel to the 45 degree angle cut.

Now you have the top piece of casing tacked in place with the ends cut at 45 degrees, it's just a bit of trial and error now. Cut a piece of scrap casing at the 45 degree angle and hold it in place. This will show you where the gaps are at the joint and you can adjust the miter saw to the correct degree to close the gap. When you have the correct degree adjusted to the miter saw you are ready to cut the next piece of casing that will be installed and have a nice tight miter. Be sure to apply the bevel technique to each cut.

Always apply glue to your miters before making the joint. Then each miter will be pinned together with a small nail at the outer corner so the nail goes through the miter to hold the two pieces together tightly. I use an 18 gauge nailer for nailing the inside of the casing to the door jamb as well as at the outside miter joint. After everything is pinned with the small gun I will use a 16 gauge gun to solidly nail the outer edge of the casing to the wall. When using the bigger gun to finish the nailing process stay away from the miter joint so you don't disturb the miter.

Finish carpentry has many little tips and tricks and these little tricks can have a big impact to the over all quality and the time it takes to finish a project.

Post from: Woodworking Training

Finish Carpentry Tips And Tricks For The Diy Trimmer

Read more on Philippine Daily Inquirer

Post from: Woodworking Training

MMDA to recruit 200 for carpentry, electrical, road work

A carpentry plan is very important to have when doing carpentry. When a person has a plan he or she is now ready to get the job done in a professional way. One charactistic that a great carpenter has is planning ahead. Here is some strategic ways to plan out a carpentry job, home improvement job, and many other projects that one may be interested in.

Have A Vision

One great way to plan out a project is first to have a vision know what you want before it is complete. This is the number one rule. If a person starts to build or work on a project and they are not sure how it is supposed to look they are surely doomed. Recently I was working in Bay Way Refinery doing scaffolding and one thing that I realized is that before building the scaffold it is very important to picture how the finish product before producing it. If I didn't things would not work out.

Make A Lisit

Making a material list is very important. Most carpenters know a material can save allot of confusion and wasted time. The material list wont always be accurate but it should be very close. Usually the list is checked twice to make sure everything is ok. Normally it is not a huge list but something small just to start out with. The list should include things to complete the job such as nails, glue, tape, paint whatever. Also create a tool list on all the tools that you will need for the job preperation is very important.

Get The Job Done

The next step is getting the job done. Putting the pieces together.Try to have fun life is what you make it so live it up and have a great time. Some carpentry projects will be more difficult than others. Love to challenge yourself it will make you a better person in the short and long run. Through out my carpentry career I have been challenged by as well but nut being persisatant is what got me through and you can do the same.

Post from: Woodworking Training

Carpentry Plan Strategy and Tactics

Carpentry can always come in handy, it is a skill that can be expanded upon once a person has learned the basic. Teen boys who want to learn carpentry should know there are some basic tools and ideas to start with. Safety always has to come first, wearing the correct protective clothing, such as goggles, gloves, boots, or some other closed toed shoes, and even occasionally long sleeves is a must. Also, removing jewelry, rings, earrings, necklaces, and anything else that could caught in a machine or attached to something can never be forgotten.

Doing these things will lessen the chance that a teen boy who wants to learn carpentry will not get hurt, injured, or injure someone else. Also, always remembering to turn machines, put the safety switches on, never leaving cords tangled or laying around where someone could trip or another machine could be damaged or cause damage to property and work placed near it.

The number of accidents that can be avoided by remembering is to always work safely and neatly. Cleaning up the work area after every project, putting tools and materials away so there is less chance of tripping or loosing tools. These things will help and create a safer environment for any teen who wants to learn carpentry. Then there are all the tools that a teen would be using. Such as some basic ones like a hammer, hand saw, nails, screws, drill, wrench, pliers, along with possibly sand paper, a grinder, and different sizes of screwdrivers. Then there are some tools that are little more advanced but are still needed for basic carpentry like planners, table saw, air compressors, lathe, power drills, and additional power tools that can even be run by the air compressor.

These tools would be needed to make basic projects like tables, chairs, book cases, and even shelves. Any teen boy who wants to learn basic carpentry would need to learn and understand how to use all these different tools if they want their projects to come out neat and sturdy.

Post from: Woodworking Training

Basic Carpentry for Teen Boys

Do it yourself carpentry or DIY woodworking as it's also known was a fad in the 1890s but it looks like it's here to stay. Unlike many of the other fads and fashions that come and go. And with so many novice DIY experts around its no wonder. Let's face it, do it yourself, can save you a bundle of cash. The only caveat to this is where does one get started? Meaning what are the basic fundamentals of starting and completing a project? Well, let's jump right in here and start the education process now.

The main rationality behind the longevity of the do it yourself carpentry segment is mainly the ease with which so many woodworking projects can be accomplished. If you begin you venture by learning the basics and building from there, then you can tackle any woodworking project. Many things which were beyond the average ordinary layman are now ordered before him in an enticing array of tools and completed products. The finished products are examples of what could be done even by the layman, and the tools are the meat hooks to take hold of him and keep him squirming on the end of woodworking. Today, most projects have a step by step outline that you follow. And once you feel comfortable with the basics and have your standard tool set, you should feel confident you will get the project done.

That's not to say that do it yourself carpentry solely relied upon the guilelessness of the unsuspecting layman, waiting to swoop at the drop of a hat. If that were the case and do it yourself carpentry didn't live up to its reputation then the fad would have died an almost instantaneous death. Nonetheless there's no gainsaying the fact that it has lived quite long lifespan as far as fads and fancies go so we can in all probability assume that do it yourself carpentry is here to stay. Many may ask - well why? There are a multitude of answers, however a few jump right out at me. First, it allows someone to do a job that otherwise would need to be done by an expert. Hence, costing a great deal of money. Besides, there is a sense of gratitude and self satisfaction when you walk into your newly remodeled kitchen and know that you are the one who made it happen.

If you've tried your hand at do it yourself carpentry, then you know exactly how fun and self gratifying it can be. Although I highly recommend picking up a few starter books, it is not a complete necessity. The option here is that you can try your hand at a prefab kit. Remember though, a basic comfortable understanding of woodworking and a standard tool kit will certainly make your project, prefab or not, go a lot smoother.

One of the biggest advantages to prefabricated kits is being able to tell you early on is if you have the patiences and motivation for DIY projects. The thing with do it yourself carpentry is that if you don't like working with your hands and woodworking tools, then it's emphatically out for you and you might have to call someone in to get some of the rougher projects in your house going. Look at it this way, by finding out up front you certainly save yourself a lot of frustration and pain. And when it comes time to hiring someone to complete the projects, well you won't feel so bad spending the money.

Other than that do it yourself carpentry is a fascinating way to get your hands around woodworking and is the easiest way to get your feet wet as well. Don't be shy, if you feel you want to try it then go for it. For starters pick yourself up a good woodworking essentials book, build your tool kit and start your home projects as soon as you feel comfortable.

Post from: Woodworking Training

Do It Yourself Carpentry Is Here To Stay

Carpentry hand tools are a necessity if you are thinking about getting into woodworking. Whether cabinetry, furniture making, or just hobby projects, there are a few basic carpentry hand tools you will need. Stanley hand tools are favored because they offer such a wide variety of woodworking tools, for many different jobs. A circular saw is a common carpentry hand tool that demands respect for safety:

General Tips on Circular Saw Safety and Use:

- Always wear safety glasses or a face shield.
- Wear a respirator or dust mask.
- Wear hearing protection to avoid excess noise.
- Check the retracting lower blade guard.
- Ensure that the blade is sharp.
- Check the saw for proper blade rotation and depth while the saw is unplugged, (the lowest tooth should not extend more than about 0.3 cm or 1/8" beneath the wood).
- Keep all cords clear of cutting area.
- Circular saws are designed for right-hand operation, be careful when using left-handed, and always use both hands when operating the saw. One hand should be on the trigger switch and the other on the front knob.
- Always be sure the power is unplugged when not in use, especially if changing blades. Stanley hand tools also include other power tools such as drills, electric screwdrivers, grinders, sanders, jigsaws, miter saws, and other carpentry hand tools for special projects. These safety tips apply to any carpentry hand tools, whether Stanley hand tools, or any of the other popular brands:

Power Tool Safety Tips:

- Perform maintenance regularly as needed.
- Use the right tool for the job and inspect before using them.
- Operate according to manufacturers' instructions
- Use personal protective equipment like steel mesh gloves for cutting and safety glasses, or respirator masks.
- Use guards that come with the power tool and use them as intended.
- Disconnect power tools when not in use. Never mess with a power tool that is plugged in to change blades, or anything else.
- Don't hold the switch button while plugged-in, to carry.
- Keep tools sharp and clean, a sharp blade cuts better and is safer.
- Remove damaged cords and discard them.
- Do not carry, hoist or lower power tools by their cords.
- Don't pull the cord to disconnect it from an outlet, simply unplug it.
- Keep cords away from heat, oil and sharp edges, and especially make sure it is not in the path of what you are cutting.

Woodworking As a Hobby Can Seem to Be Overwhelming:

When you first start woodworking, it can seem overwhelming to assemble all that you are going to need. When it comes to carpentry hand tools, it is better to save for a good quality power tool, like Stanley hand tools, than to buy a cheap, off-name brand. Your carpentry hand tools are an investment that will last you for many years, and Stanley hand tools come with a warranty.

Buying Great Hand tools:

Buying great hand tools is easy, if you choose a reputable manufacturer, and Stanley discount tools are a leading brand for carpentry hand tools. The main thing is to accumulate your carpentry hand tools as you need them for individual projects.

Post from: Woodworking Training

Woodworking Hand Tools – Select the Right Carpentry Tools

Finish carpentry came to be as an artistic craft where exactitude is crucial.  It is mainly interior trim that may come in various works including decorative moldings, casings, fine woodworking, cabinetry, joinery, furniture making but may still be used to amplify beauty in exterior jobs such as decking, siding and roofing.  Because its results is what is most noticeable than any other phase in construction, it is often considered to be the most important part of a remodeling project.  

But other than just a side-job for your home remodeling project, finish carpentry can also be a project on its own.  As it maximizes appeal, your New York home would surely benefit from the boost in overall value.  It is a project worth looking into to bring the most bang to your every home improvement buck whether you are in Manhattan, Staten Island, Brooklyn, Queens, or Long Island.

There are a lot of possible projects that you could undertake involving finish carpentry and here are several of the most common:

Interior Trim

Trims are closely associated with moldings and can be applied to a good number of interior features like baseboard, pilasters, columns, mantels, pediments, corbels, fireplace surrounds and spandrels.  The simplest trims come as flat boards made to accent a certain area.  Depending on the style that you want to achieve out of your finish carpentry project, different materials can be used such as plywood and battens, panels, frames, bead board, or tongue-and-groove boards.   

Moldings

Moldings, more popularly known as decorative moldings, can add a touch of classic elegance, modern sophistication or simply put—drama into just any room.  As decorative molding comes in a very wide variety of styles and sizes ranging from stock patterns to custom cuts, shop for a one designed to complement with the overall décor of the room.  In a finish carpentry project, even the simplest of molding design can add volumes to the room’s beauty.  

Door and Window Casings

These types of casings are what fill in the gaps between doors, windows and the surrounding walls.  The success of a finish carpentry job where doorways or window frames are to be cased lies in the accuracy in cutting, perfect squaring of corners and right positioning while nailing the rest of the casing.  Though the tasks may seem easy, they are actually a far-cry from what many homeowners perceive them to be.

And now comes the big question- Why hire a finish carpenter?  First off, finish carpentry requires a good eye for proportion and detail, woodworking skills and craftsmanship that only a set of good fruitful years of experience can afford.  Whether working with traditional wood other construction materials manufactured through technological advancements, proper installation is vital.  

If you decide to go for DIY finish carpentry project with savings in mind, then you are on the wrong track.  Why?  Simply because, by doing the job without the needed expertise, you are risking the results probably wasting not only the materials, time, effort and money; but you are also exposing your homes to damages which may be caused by your attempts.  Thus, finish carpentry is best handled by professionals.

Post from: Woodworking Training

All About Finish Carpentry

Shop class probably made you fall in love working with tools. It gave you the chance to make a table,  chair or even a bird house. But there are other things you need to learn if you want to pursue carpentry career so after graduating from high school, make it a point to go to carpentry school.

There are many carpentry schools all across the country so you don’t have to move out of town or state. You should first check if this is being offered in the nearby community, technical or vocational college.

If there is one, find out what does their curriculum cover. It should have subjects such as math, estimation of costs of jobs, times and materials, use of equipment and tools as well as various techniques in carpentry.

Another thing you have to consider when you select a carpentry school is which career in carpentry you are striving for. Is it to pursue  a residential or commercial career in carpentry? The difference between the two is that you can start a residential carpentry career in less than half the time it will take to be a commercial carpenter because the latter requires more skills and even certification.

For those who are not sure yet why they want to do, pick a school that offers both residential and commercial carpentry training. This will give you time to study how to install doors, frames, roofing systems, scaffolding and a host of other things making you a well rounded professional.

You should also consider how much the tuition is. Can you afford to study in this school? If you can’t, don’t give up just yet because they may have a scholarship program that you can avail of.

Apart from schools in the neighborhood, you can also enroll in such a course online. You get to learn the same things as though you are in the classroom and at the end, you also get certification upon successful completion.

If the program or money is not an issue, the only thing you have to worry about now is the success rate of people who graduated from the program in finding a job. Some of these schools may not have a job placement program which means you have to look for one yourself. Others are more helpful because they have tie ups with carpenter contractors or with the various carpentry associations.

Once you have all the information, try to narrow down your options to at least 3 to 5 schools. You then review what each one can offer to students and which of these is favorable to you. From there, all you have to do now is enroll in be willing to accept the training they are giving you. 

You don’t get a bachelor’s degree in carpentry when you finish a program given by the community, technical or vocational college. What you have in your hand is a simply a certificate of completion which makes you someone qualified to work in that profession.

What you do after you obtain your certificate is up to you. If you want to work right away, find employment as an apprentice. To further enhance your skills, it will be a good idea to pursue higher education so you can work in a specialized field in carpentry. If you want to be your own, then start your own carpentry contractor business.

You have a lot of options and going to school is the first step when you decide to pursue a carpentry career.

Post from: Woodworking Training

A Carpentry Career Begins in School

If you are a carpenter or are considering a career as a carpenter, you are probably curious about carpentry books. A carpenter is someone who builds things out of wood. Carpentry books give you valuable information about what carpentry is and the basic practices of a carpenter.

Like any other job, you may sometimes have questions. This is where a carpentry book will come in handy. Usually, carpentry is a learned trade. Most people do not go to school or complete any kind of training to become a carpenter. They either learned it from their relatives (father, grandfather, etc.) or they learned it on the job. Many times a builder will hire an inexperienced person to be there "toter" or helper. This person starts out carrying tools and nails for a carpenter. Soon, he learns to measure and cut wood, and before long he learns the basics of carpentry. This type of on the job training is common is the world of carpentry. Because these people are learning as they go, it is helpful to have carpentry books available to refer to when you get stuck.

In most cases, carpentry is pretty simple. But there are those tasks that seem tedious and almost impossible if you don't have any carpentry books to show you the way. It is also crucial if you are new to the field, to have carpentry books to read while you are learning. It is easy for your boss to forget to show you all the ropes when he is in the middle of a building project (which he most always is).

There are many tools involved in carpentry. Long gone are the days of hammers and nails. These days carpenters use heavy duty and expensive nail guns, a wide variety of different types of nails and screws, saws, and drills, and everything in between. It can be overwhelming to know what you need for which task without the help of carpentry books. In fact, many of the saws look similar and it is easy to forget which one does what.

Carpentry books are a valuable and necessary addition to your tool belt. Even if you don't have the liberty to stop to read them on the job, studying over them in your spare time can save you time and money in the long run because it will prevent unnecessary mistakes.

Post from: Woodworking Training

How Carpentry Books Can Help Your Carpentry Career?